Skip to content

Advanced options#

This group of menus provide some global advanced options for the Hex-dominant mesher.


Advanced Options General

In this menu, there exist three checkboxes to enable or disable the execution of the main steps of the meshing engine:

  • Castellated mesh, which performs cell splitting and refinement of edges, surfaces, and cells.
  • Snapping, which snaps the points of the cells that intersect the geometric surface onto the surface to create body-fitted cells.
  • Layers addition, which constructs layers of cells on the simulated geometric surface for better capture of boundary layer effects.


Advanced Options Refinements

In this menu, some options related to the refinement process are specified:

  • Max local cells: the maximum number of cells per core.
  • Max global cells: the maximum number of cells in the whole domain.

Note: the max local cells and max global cells are used to control the refinement in the castellated mesh step. In case of serial meshing, both values are the same. The meshing engine will continue refining the cells according to the set refinement criteria until max local cells is reached for certain core (this core will not refine anymore with other cores continuing refinement for other sub-domains or the engine would re-balance the loads between the processors and then continue refinement for all sub-domains) or max global cells is reached globally.

Min refinement cells#

This specifies the minimum number of cells for a refinement iteration to be executed. The purpose of this value is to prevent the engine from spending a lot of iterations refining a small number of cells.

Cells between levels#

This specifies the number of layers in a buffer zone between zones of different refinement levels. Increasing this value would create a more gradual change in layers of refinement between zones at the expense of mesh size.

Resolve feature angle#

In the surface refinement step, a minimum and a maximum levels of refinement are specified. If a cell intersects the geometric surface at an angle greater than the resolve feature angle the maximum level of refinement is applied to this cell. Otherwise, the minimum level is applied.

Allow Free Standing Zone Faces#

If this checkbox is ticked then all the faces that intersect a geometric surface are put in a facezone. If it is not ticked, then the geometric surface is checked. If it has a facezone only and no cellzone, then the faces that intersect the geometric surface are put in a facezone. If the geometric surface has both facezone and cellzone, then faces are removed if they are between the same cellzone or on the boundary.

Planar Angle#

This is used to determine if surface normals are the same or opposite. A default value for it would be the resolve feature angle.

Max Load Unbalance#

This value will tell the engine how much imbalance between the processors is tolerated. Setting this to 0 will force the engine to balance the loads between the processors.


Advanced Options Snapping

Some options related to point snapping onto a geometric surface are specified.

Solver Iterations#

This is the maximum number of iterations for the snapping process. More iterations mean better quality but at the expense of computational time.

Smooth Patch#

Specifies the number of iterations for mesh smoothing to make the mesh conforming to the surface.


This defines the relative distance from the surface along which the engine would look for points to snap onto the surface. It is defined as a ratio of the length scale of the cell and its minimum value is 1.

Relaxation Iterations#

This specifies the number of relaxation iterations for snapping.

Snap Feature Iterations#

This identifies the iterations limit for snapping points onto the features of a geometric surface.

Multi Region Feature#

Tick this checkbox when dealing with a multi-region mesh so that features between multiple surfaces are captured.


Advanced Options Layers

The options related to the Layering process are defined here.

Relative Sizes#

By ticking this checkbox, the lengths defined in the layering section are defined relative to the length scale of the grid cell over which the layer is being constructed. Not ticking the checkbox makes the lengths defined absolute.

Expansion Ratio#

This specifies the default global ratio of the geometric progression defining the boundary layer. This value is overwritten by the expansion ratio defined per surface in the layering section.

Final Layer Thickness#

This is the default global thickness of the final layer of any boundary layer. Also, this value is overwritten by the final layer thickness defined per surface in the layering section.

Min Thickness#

This is the default global minimum allowable thickness of any boundary layer. Also, this value is overwritten by the min thickness defined per surface in the layering section.

Feature Angle#

This specifies the maximum angle of a surface features after which the meshing engine does not add a layer at this location. Increasing this value (say to 180 degrees) is suitable to have layers over sharp corners.

Slip Feature Angle#

If the angle between a patch's extrusion direction and its neighbor's exceeds this value, then point sliding on the patch is allowed. The default value is one half of the feature angle.

Relaxation Iterations#

The global maximum number of relaxation iterations.

Relaxed Layer Iterations#

Up to this number of iterations, the meshing engine will iterate to satisfy the quality criteria. After this number of iterations, if a quality criterion is not satisfied, the engine would use the corresponding relaxation value defined in the quality section.

Surface Normals Smoothing Iterations#

This specifies the number of iterations required to smooth the surface normals.

Interior Mesh Smoothing Iterations#

Specifies the number of iterations for smoothing the directions of mesh motion.

Smooth Layer Thickness#

Specifies the number of iterations to smooth the layer thickness over a patch.

Max Face Thickness Ratio#

Specifies a limit for the ratio of a layer's face area to its thickness over which the engine will not add a layer to this face so as to avoid highly warped cells.

Max Thickness To Medial Ratio#

If the ratio between a layer's thickness and the medial distance exceeds this value, then the engine reduces the layer growth.

Min Medial Axis Angle#

This specifies the minimum angle for medial axis point selection.

Number of Buffer Cells#

Specifies a buffer region where the number of layers is gradually decreased. If this value is set to less than 0, a terminated layer is stopped right away.

Layer Addition Iterations#

The maximum number of iterations for the layer addition algorithm.

Layers Not Grown#

This specifies the number of layers whose extrusion is cancelled because they are close to features and/or patches where layers are not grown. This is used as a transition between regions of no layers and regions of full number of layers.


Advanced Options Quality

Some global quality criteria are defined here.

Max Non Ortho#

This specifies the maximum allowable face non-orthogonality angle which is defined as the angle between the actor connecting the centers of two adjacent cells and their common face normal.

Max Boundary Skewness#

This specifies the maximum allowable skewness of a boundary face.

Max Internal Skewness#

This specifies the maximum allowable skewness of an internal face.

Max Concave#

This specifies the maximum allowable cell concavity in degrees.

Min Flatness#

The minimum allowable face flatness which is the ratio between the face's projected area and its actual area.

Min Vol#

This specifies the minimum allowable cell volume.

Min Tetrahedral Quality#

The minimum allowable tetrahedra cells quality.

Min Area#

The minimum allowable face area. If it is set to a negative value, then all face areas are accepted.

Min Twist#

The minimum face twist which is calculated as the dot product of face normal and the face centre triangles normal.

Min Determinant#

The minimum allowable cell determinant. A value of 1 corresponds to a Hexahedron.

Min Face Weight#

The minimum allowable face interpolation weight.

Min Vol Ratio#

When a cell's points are snapped to a surface, if the new volume is larger than this ratio multiplied by the old volume then this cell is deleted. If the ratio is set to a negative value, the cell is always deleted.

Min Triangle Twist#

The minimum allowable triangle twist which is the dot product of consecutive triangle normals resulting from face-centre decomposition.

Smooth Scale#

This specifies the number of smoothing (error distribution) iterations.

Error Reduction#

This represents the amount of scaling back the displacement at error points.

Last update: June 9, 2022
Back to top